Novy firmware UBNT 5.2

[michal.siman]

Version 5.2 - Final Release (May 14, 2010)
------------------------------------------

- New: Speed test tool
- New: AirView tool (Spectrum Analyzer mode)
- New: Routing scenario: Network mode "Soho Router"
- New: NanoStation M5/M2 Second Ethernet port functionality -- now it is possible to bridge with wireless port
- New: Antenna gain and cable loss fields for compliance
- New: AirMax ON in default configuration
- New: Intelligent GUI improvement
- New: Console agent: Restore active heartbeat connections after firmware upgrade
- New: Report 802.11 information messages into syslog
- New: Improve ACL rules management: increase max MAC ACL entry count to 32
- New: Remove DFS 5250-5350 frequency for US country code (all M series products)

Improvements/Change requests:

- CCR: RADIUS client support in AP mode
- CCR: PEAP/MSCHAPv2 support
- CCR: Add static routes via WEB UI
- CCR: Show Station and AP IP address
- CCR: Hide WPA password with "*"
- CCR: Ability to de-associate station from Station list via WEB UI
- CCR: Add support for SSH authorized keys in configuration file
- CCR: Change apply configuration logic
- CCR: Missing ppp0 interface information on Main page, when PPPoE session is initialized
- CCR: Add System Startup Time/Date field (critical for 802.1x supplicant)
- CCR: Allow ping when device is in TFTP recovery mode
- CCR: Include PPTP/GRE NAT modules
- CCR: Add MAC clone/change option for WAN interface when operating in SOHO router mode
- CCR: Report AirMax priority and AMQ/AMC in Station detail
- CCR: Speed test: Show total throughput (RX + TX)
- CCR: Make IP address in stations list as hyperlink
- CCR: GUI: Show/hide Traffic shaping configuration
- CCR: GUI: Add option to enable/disable NAT modules on router: SIP, PPTP, FTP, RTSP
- Improvement: Speed test: resolves TX/RX difference
- Improvement: In memory allocation

Fixes:

- Fix: TX Power improvement for NanoBridge M5, AirGrid M5, NanoStation Loco M5, Bullet M2, Rocket M2, NanoStation M2, NanoBridge M2
- Fix: Chain signal mismatch on reported signal strength/ Power control for M5 2x2 chain devices
- Fix: Sometimes Auto ACK values gets too high
- Fix: Max power level for Australia
- Fix: Speed test + AirMax PtP No Ack combination crashes AP
- Fix: Traffic Shaping is not functional except Soho Router mode
- Fix: Traffic Shaping Burst is for functional
- Fix: WPA security : Sometimes station is disassociated from AP
- Fix: Broadcast traffic is duplicated on AP-WDS
- Fix: NAT protocols state changes when changing security
- Fix: SNMP wrong OID type: Disallow port range as destination (to private subnet)
- Fix: SNMP reports incorrect wireless stats
- Fix: Station can not connect to AP (MAC Locked) if it was connected to another AP with the same SSID
- Fix: Signal reporting
- Fix: Improve noise level calculation
- Fix: Noise floor is too aggressive
- Fix: Auto ACK on AP
- Fix: No more trimmed channels on Compliance country code

- Fix: Airmax: PTMP ping loss issue after beta6
- Fix: AirMax: PTPNack AMQ/AMC fluctuation
- Fix: AirMax: PTP and PTMP enhancements (latency)\

- Fix: Airview: Sometimes switching back to normal operating mode is endless

- GUI fix: Problems with WPA PSK paraphrase: old value is displayed, new value is not saved
- GUI fix: Sometime Device name in not reported in Stations list
- GUI fix: Do not show clients as connected when authentication key is not valid
- GUI fix: Test mode. Timing is no so precise as stated in the warning message
- GUI fix: Need correctly display ACK/Distance when AirMax and PtPNoACK mode is enabled
- GUI fix: Name -> Device Name
- GUI fix: Grammar error in warning message
- GUI fix: MCS1 is always reported in AP/Station statistics
- Fix: IE8 and WEB UI errors

- Fix: Frequency list issue fix for counties:
Uzbekistan
Brazil
Honduras
Peru
Philippines
Russia
South Africa
Sri Lanka
Thailand

Known issue:
- Limitation from HW: MCS13 does not work with WEP/WPA/WPA2/WPA-TKIP/WPA2-TKIP security -- MCS 13 removed from WEB UI

[michal.siman]

Hodne pekna vec je moznost OTESTOVAT nove nastaveni. Proste udelate zmenu, date zmenit a nahore se objevi klasicky ze se zmenila konfigurace a jestli to chcete provest, ale tady je navic tlacitko TEST, zmacknete, ono se to zrestartuje a provede se nove nastaveni no a zacne se odpocitavat tri minuty, do te doby muzete dat ze ponechat zmeny (uz se znovu nerestartuje) a nebo se to po trech minutach samo vrati zpet jak to bylo. moc hezky. presne tohle chybi v RoS

[hapi]

to přece v RoS je taky, teď nevim jakou kombinací kláves ale když tě to odpojí, vrátí se nastavení tzv. safe mode nebo jak tomu říkaji.

[michal.siman]

to přece v RoS je taky, teď nevim jakou kombinací kláves ale když tě to odpojí, vrátí se nastavení tzv. safe mode nebo jak tomu říkaji.

ano, mas pravdu, v nejakym tom safe modu to funguje, ale ve winboxu (se kterym pracuju nejcasteji) tato volba pokud vim neni.

[erotel]

to přece v RoS je taky, teď nevim jakou kombinací kláves ale když tě to odpojí, vrátí se nastavení tzv. safe mode nebo jak tomu říkaji.

ano, mas pravdu, v nejakym tom safe modu to funguje, ale ve winboxu (se kterym pracuju nejcasteji) tato volba pokud vim neni.

Otevřít winbox -> new terminal -> ctrl+x (nezavírat terminál).Aktivuješ si safe mód(pokud se odpojíš vrátí se funkční nastavení) a normálně pracuješ ve winboxu.

[Ladik]

Ha a kde je ta "funkcni" regulace pro napr: Rocket M5 s 30dBi parabolou?
Pro stouraly mam to doma a nereguluje to do normy !

Ahoj Lada

[michal.siman]

Otevřít winbox -> new terminal -> ctrl+x (nezavírat terminál).Aktivuješ si safe mód(pokud se odpojíš vrátí se funkční nastavení) a normálně pracuješ ve winboxu.

no vidis, zase jsem o neco chytrejsi

[soooc]

Spektrak, ktery je vevnitr je SKVELY! Povinne pouzivat nez nekomu vlezete na kanal:)

[Ladik]

Regulace funguje do min hodnoty 8dBi, takze s tou jejich parabolou 30dBi je to nepouzitelne a navic pokud to stahnu na minimum tedy na tech 8dBi, tak to jede 10x pomaleji a rozpada se spojeni.

Spektrak jsem nezkousel, mrknu na nej.
Ahoj Lada

[Stanislav Hrncir]

Spektrak, ktery je vevnitr je SKVELY! Povinne pouzivat nez nekomu vlezete na kanal:)

už sem ho zkoušel včera když mi ten fw posílal jeden expert z ubnt na test, velice pěkné..už jenom kvůli tomu se hodí pořídit bullet M a na to nějakou yagi..

[rouchi]

a proč bulelta a jaginu ??? kup airgrida a můžeš to napájet přímo z USBčka z notebooku, takže ani nebudeš potřebovat elektriku...

[Stanislav Hrncir]

myslel sem tím na odchyt rušičů a jiných běsů, tam to chce co nejmenší úhel..

[petr]

Regulace funguje do min hodnoty 8dBi, takze s tou jejich parabolou 30dBi je to nepouzitelne a navic pokud to stahnu na minimum tedy na tech 8dBi, tak to jede 10x pomaleji a rozpada se spojeni.
...

Nastav:
Antenna Gain: 30dB
Cable Loss: 2dB (např.)
Zaškrtni Obey Regulatory Rules a rázem máš Output Power 1dBm

Mě to běží na 9,5km na 20MHz kanálu zhruba 60Mbps (při MCS 13-14) - změřeno Bandwithtestem na připojených MK

Pozn: Je nutné použít Security WPA-AES nebo nic, jinak se spojí nejvýš na MCS 12

[pcwifi]

a skutecne je na vystupu pouze a jen onen 1db ? pokud jo a udela to i tebou zminenych 9km,tak je to exelentni...

[Ladik]

No jo, ale chce to po me nastavit WDS peers.
Nevite co to je?
Nastavene tam nic nemam a jede to, ale pri zmene jak pises to chce doplnit to WDS peers.

Ahoj Lada