5.6.1

[midnight_man]

Version 5.6.1-Service release (July 3, 2015)
-------------------------------------------------
New:
- New: Private SNMP MIB
- New: IPv6 support
- New: Manage custom scripts
- New: Extend Statistics reporting - TX/RX reporting improvement
- New: Extend Statistics reporting - Latency for each Station
- New: Statistics - ACK/Distance display
- New: Report remote TX power in AP/STA info
- New: Show RX Signal per Chain
- New: Add firmware prefix reporting for any model (TI/XM/XW)
- New: Display actual operating frequency range in MAIN page
- New: Show radio mode in Site Survey scan results
- New: DHCP address reservation
- New: Implement QOS for VLANS
- New: Increase password length to more than 8 symbols
- New: Increase MTU/MRU to 1500 bytes for PPPoE (server must support max-payload tag)
- New: airMAX devices will support only WPA-AES/WPA2-AES security (WEP optional for AP-Repeater mode)
- New: Channel shifting is removed. Frequency selection in 2MHz/5MHz steps available when in airMAX mode
- New: TCP support for remote system logging
- New: DynDNS More providers supportÂ
- New: Linux kernel update to 2.6.32.65
- New: Upgrade lighttpd 1.4.35
- New: Update hostapd/wpa_supplicant to the latest available stable version (v2.1 final)
- New: Upgrade libevent to 2.0.22
- New: Upgrade dropbear to v2014.63
- New: Upgrade OpenSSL to 1.0.2a

Fixes:
- Fix: Device hangs on startup when DHCP relay is enabled on two LAN interfaces
- Fix: Long Range PTP mode stops passing traffic on high load (XW)
- Fix: Sometimes AP can’t change channel after RADAR detection
- Fix: airGW provisioning creates wrong forward rules in case of PPPoE client configuration on WAN interface
- Fix: Broadcast goes from one STA to another STA even if Client Isolation function is enabled on AP
- Fix: Report DFS Wait or DFS Radar in MAIN page
- Fix: AP drops all stations. Recovers after reboot. (XW)
- Fix: Crash during upgrade from v5.5.x when parsing incorrect IPTABLES rules
- Fix: Update EIRP limits for Australia according channel bandwidth
- Fix: Allow 0.0.0.0 Fallback IP for PPPoE client configuration
- Fix: Various DFS and Frequency List usage improvements
- Fix: Speed test low values when using Management VLAN
- Fix: DFS improvements for Czech Republic
- Fix: airSelect can use only non-DFS frequencies
- Fix: No full-restart when changing ACL list first time after upgrade to v5.6.x
- Fix: Wrong 32 symbols SSID reporting to airControl
- Fix: Remote statistics reporting to client keeps Android phone wake up all the time
- Fix: Update EIRP limits for Brazil
- Fix: PPPoE MTU/MRU limited according to parent interface settings
- Fix: Traffic stops after Site Survey execution on remote Station when hidden SSID is set on AP
- Fix: M900 radio fails initialisation in heavy noise environment
- Fix: STA Device Name is truncated in SNMP reporting
- Fix: SNMP string sizes
- Fix: Station can't connect to AP with Hidden SSID (XW)
- Fix: Discovery response leak across VLANs
- Fix: Station shows wrong "TX Signal" in AP details window
- Fix: The same channel numbering for 4920-5000MHz and 5920-6000MHz (Compliance Test).
- Fix: Disable UPnP SSDP messages in Syslog
- Fix: Main tab is empty if device name contains <tab> symbol
- Fix: Scan results buffer size limit issue (at ~200 APs found)
- Fix: Reduce TX power to the EIRP Limit when radio is operating in Station mode or Auto frequency selection is chosen for AP
- Fix: Speedup DHCP and PPPoE clients to update IP settings after successful WPA authentication
- Fix: SSL v3 POODLE vulnerability
- Fix: Add 5GHz frequencies for Kazakhstan
- Fix: Validate ping interval for Ping Watchdog. It can’t be set to 0 sec.
- Fix: Improved Wireless page loading routine
- Fix: AirMax Capacity/Quality calculation/reporting with Fixed Rates
- Fix: TX flow control and multi queue support. (XW)
- Fix: Error after run Speed Test (XW)
- Fix: ACK/Distance miscalculation when connecting to XM AP. (HT8, HT30, XW)
- Fix: AP/STA performance issues (XW, airMax)
- Fix: HT20 Rates are reported/used when device is configured to operate in HT40 and fixed rate is selected. Alternative rate module selected
- Fix: Site Survey does report the same NF value for each channel (XW)
- Fix: Strange AirView view on Rocket M5 Titanium (XW)
- Fix: airSync does not work with fixed rates (XW)
- Fix: Radio has to fallback to full channel list if configured Frequency List is enabled but doesn't contain valid frequencies (XW)
- Fix: Remote Syslog message type is "unknown"
- Fix: Last IP isn't taken from VLAN tagged packets (XW)
- Fix: RADIUS accounting issue (XW)
- Fix: Selecting SSID on HT40 may change Channel width from 'Auto HT20/40' to 'HT20'
- Fix: Disable ACK slider if AirSync/Long range PtP selected
- Fix: Antenna alignment tool (beeper) crashes on iPhone, iMac, etc.
- Fix: Don't suggest WPA key as Username for login save (Firefox)
- Fix: Wireless page is broken (IE8/9)
- Fix: XW: Improved Data Rate selection for Default rate algorithm when operating in noisy environment
- Fix: Remove 924MHz (shifted frequency) as it’s out of allowed band range (10MHz channel width)
- Fix: Add full product name in discovery reporting
- Fix: AP crash with Multicast Enhancement enabled and specific multicast traffic on STA association
- Fix: Scan results ageing issue
- Fix: Ping tool doesn’t execute ping in 1sec interval
- Fix: Ping tool ping count is sometimes higher than defined
- Fix: Unable to set empty PPPoE password (Chrome specific)
- Fix: Proper antenna polarisation selection for 802.11abg support
- Fix: Some frequencies were missing for India when 30MHz channel width is selected
- Fix: Improved association with older devices
- Fix: Escape quotes for Device Name and SSID in Station List
- Fix: Make ‘Feed only -3dBi’ as default antenna selection for appropriate models
- Fix: XW: WPA2-PSK Association time out in case of long channel list
- Fix: Min TX Power for NanoBridgeM5 should be -8dBm
- Fix: Discovery returns wrong product name
- Fix: Speedtest duration validation in range [1-99]
- Fix: Reload newly uploaded configuration file
- Fix: ac-agent doesn't send GPS coordinates read from GPS module
- Fix: STA continuous crash when connecting to Apple AirPort AP
- Fix: AP doesn't initiate re-authentication to RADIUS server when Station re-associates
- Fix: EAP TTLS/PEAP do not check time in TLS session
- Fix: WEB UI: Can’t logout on high CPU load
- Fix: Discovery shows empty Device Name if length is 64 symbols
- Fix: Italian translation updates
- Fix: Spanish translation updates
- Fix: Simplified Chinese translation updates

Improvements:
- WEB UI: Disable controls while Speed Test is in progress
- WEB UI: Show explanation after move mouse on RX/TX Signal labels
- WEB UI: Ordering by frequency improvement
- WEB UI: Site Survey results sorting improvements
- WEB UI: Update “Long Range PtP Mode” help message
- WEB UI: Change EIRP Limit warning message and Auto Adjust to EIRP Limit label
- WEB UI: Increase TEST mode timeout for DFS frequencies
- WEB UI: Don’t allow to select AP with unsupported security mode in Site Survey
- WEB UI: Port forwarding from LAN side when accessing WAN IP (NAT loopback)

[raven-il]

Mate nekdo nasazeno ?

[Kaja]

Tech oprav je tam opravdu hodne.

Mate nkdo tuseni co znamena:
Fix: Various DFS and Frequency List usage improvements

Fix: DFS improvements for Czech Republic
Increase TEST mode timeout for DFS frequencies

K

[klima]

Dnes jsem to nasadil cca na 10 spoju a zvysila se latence a obcas nejaky PL. Monitoruji na zabbixu, tak to bylo znat hodne na grafech.
Testoval jsem jeste na AP sektoru na Rocket M5 a nez se tam pripoji klienti kvuli DFS, tak to kolikrat trvalo i 15min
Takze u me asi ne.
Dal jsem z5 zase 5.5.10

[ludvik]

Zkus prasárničku ... ale kanálu 5640 se vyhni ručně.

Kód: Vybrat vše

echo "/usr/sbin/radartool cactime 1000" > /etc/persistent/rc.poststart
echo "/usr/sbin/radartool -i wifi0 usecac 0" >> /etc/persistent/rc.poststart
chmod +x /etc/persistent/rc.poststart
cfgmtd -w -p /etc/
reboot

[placek.milan]

Mate nekdo nasazeno ?

Měl jsem asi na 10 spojích beta verzi 5.6.1 a bez jediného problému. Tuhle jsem dal na pár spojů a žádná změna k horšímu. Za mě dobrý, je fajn vidět všechny ssid v survey a zjistit zdali jedou s airmaxem, v enku nebo v áčku či dokonce v ácéčku.

[p79wifi]

nasadil jsem to na skoro vše co sem stihl, a jedinej error je s tím DFS, to sou fakt tataří, tak že všude vypnout přes příkaz nebo jinou zem protože
fakt nechápu co tím chtěl kdo říci, když se mi bude X krát za den vypínat rádio a čumět několik minut, to je fakt oničem a to sem čekal
že tuto bude opravdu odladěné nebo vypnutelné, jinak to chodí skvěle, lépe než 5.5.10 a 5.5.4 u XM.

[ludvik]

No ... bohužel UBNT si to samo nevymyslelo.

[dubrma]

Přes ssh ladím frekvenci a na této verzi to trvá déle = cca 40s, oproti 5s u předchozích verzích.

Je na Mikrotiku stejně problematické vypnout DFS?

[midnight_man]

Stale to dlho riesi DFS takze na AP treba spravit SSH hack.

[raven-il]

Co propustnost stabilita a odolnost proti ruseni ?

[jopo]

Dnes som to nahodil pokusne na 20 klientov a jedno AP. Signal klesol vsade o -1db, airmax quality niekde stuplo - hlavne na klientoch kde bol slabsi signal, ale niekde aj dost kleslo (az do 10%). Rusenie a stabilita sa uvidi casom. Upgradovane z 5.5.8 a 5.5.10, XM aj XW verzie.
Zatial to davat nejdem.

[midnight_man]

je to poho, upgradujeme to kde sa da...oproti 5.5.10 nevidim nejak v kvalite linky ziadne zmeny?...

[miko]

Napodobne. V aircontrole plny scheduler, nech to upgraduje pocas hlbokej noci... Nic nezhavarovalo, vsetko slape.
Sere ma len chybajuca latencia a Tx signal level v SNMP. A v UBNT sa tvaria nahluchly, asi je to big problem zaimplementovat alebo co.

Este ohladom Rocketov Titanum - skusil niekto tento fw??? V AP mode mi to zhadzovalo klientov, musel som to vzdy restartovat.

[rado3105]

Neviete ci tie rprikazy je mozno pridat nejako hromadne - myslim ten dfs hack....(cez aircontrol napr.)