What's new in 5.0 (2011-Mar-31 11:33):
*) route - fixed cause of crashes when handling multipath routes;
*) route - fixed limit on maximum active IPv6 route count,
was causing issues with more than 2000 active routes;
*) ipsec - added command kill-connections under remote-peers;
*) ipsec - fix responder side phase2 negotiation problem
which prevented more than one Windows7 host to initiate SA;
*) fixed vrrp - interface was invalid after undoing remove;
*) winbox - added more detailed /interface ethernet stats;
*) winbox - added ability to send e-mail;
*) winbox - added missing 'set-metric' parameter
in 'Routing/Prefix List';
*) wireless - 802.11 dynamic distance fix;
*) fixed problem - packages could not be uninstalled if disk was full;
*) fixed problem - some of the RouterBOARDS did not reboot properly sometimes;
*) fixed problem - VLANs on bridge interface did not work;
*) ssh - client supports public key authentication;
Toto je původní verze internetového fóra ISPforum.cz do února 2020 bez možnosti registrace nových uživatelů. Aktivní verzi fóra naleznete na adrese https://telekomunikace.cz
Verze 5.0
- maacher222
- Příspěvky: 70
- Registrován: 15 years ago
- antispam: Ano
- Bydliště: Raslavice
- Kontaktovat uživatele:
Verze 5.0
0 x
- maacher222
- Příspěvky: 70
- Registrován: 15 years ago
- antispam: Ano
- Bydliště: Raslavice
- Kontaktovat uživatele:
hapi píše:všimli jste si že linky na v3.30 zmizely z ofiko stránek?
teraz je zasa legacy 4.17, stable 5.0 posunute to je viac menej
0 x
-
- Příspěvky: 575
- Registrován: 15 years ago
tak nevím, co se jim na tom nezdá ale prakticky celou éru prerelasů i celých relasů V5 testuju na labu s x86 proti RB800 a s NV2 nikdy problém nebyl..a pokud by nejelo jakože nebylo zapnuté tak na 11n pojede 300mbit rate a ne jenom 270ka tak nevim
0 x
hapi píše:co znamená u RBček u ethernetů blink a co znamená u wifin bridge mode? Mikrotik by měl nějak aktivně informovat o nových věcech.
kde čteč to blink? bridge se tu už řešilo http://wiki.mikrotik.com/wiki/Manual:Wi ... tion_Modes
0 x
tak to bude nějaká novinka a možná ještě ani MT team neví co přesně to bude dělat
0 x
-
- Příspěvky: 575
- Registrován: 15 years ago
For some Ethernet NICs it is possible to blink the LEDs for 10s. Type /interface ethernet blink ether1 and watch the NICs to see the one which has blinking LED.
0 x
- lwq
- Příspěvky: 1659
- Registrován: 18 years ago
- antispam: Ano
- Bydliště: MistyMountain
- Kontaktovat uživatele:
A to blikani LEDky u eth je k cemu ?
Kazdopadne nv2 na x86 mame a uz i pouzivame uplne v klidu - tak nevim co sem jim nezda ...
Kazdopadne nv2 na x86 mame a uz i pouzivame uplne v klidu - tak nevim co sem jim nezda ...
0 x
LWQ ... Vice na www.lwq.cz (treba GIOM 3000 atp.) ...