classic.ISPforum.cz

What's new in 3.17:

*) added support for Intel 10Gb PCI Express driver;
*) made Huawei E220 USB modem work again;
*) added support for Novatel Wireless Ovation MC950D HSUPA;
*) fixed PCQ fairness when pcq-total-limit is reached;
*) fixed fetch tool to work when dst-path is not specified (broken in 3.16);
*) fetch tool - added keep-result command line argument;
*) allow to specify routing-table for ping, trace-route, and telnet;
*) fixed an IPsec bug;
*) fixed /ip firewall address-list;
*) added propagate-ttl option for MPLS;
*) fix very long wireless scan-list issues;
*) fixed problem - sometimes PCQ could stop data pass-through if pcq-rate was set;
*) fixed problem - L2TP could stop working when one of clients stopped responding
at wrong time;
*) fixed problem - reduced size of supout.rif files;
*) graphing - support for 10 Gbit interfaces;
*) routing-test - added support for multi-instance OSPF;
*) user manager - fixed bug for PayPal payments with long parameter list;
*) user manager - database load command supports external storage
for temporary files;
*) user manager - added support for all UTC time-zone offsets,
including +5:30, +5:45, etc.;
*) allow queues to have all traffic, not only ip (for example vpn)
*) improved ipv6 sniffing
*) improve torch and sniffer behavior under high load
*) improved queue statistics

rb113 z 3.16 na 3.17 OK

RB411: z 3.16 (fw. 2.18) na 3.17 - OK
RB433: z 3.15 (fw. 2.18) na 3.17 - OK

je to beta, nebeta, rc nebo jaka testovaci verze tentokrat ?

reset píše:je to beta, nebeta, rc nebo jaka testovaci verze tentokrat ?

stable ...

RB 411 v3.7 - v3.17 OK

RB 450 z 3.16 na 3.17 v pohodě

X86 p4 3GHz nenabehl.

RB133 z fw. 3.9 na fw 3.17 po upgradu bylo potreba restartnout wifi karty [Wireless (Atheros AR5213]

RB600 z fw 3.15 na fw 3.17 vse ok

Zdravim

2x RB 133 - vsetko ok

a vyriesil sa s tym problem pri PPTP bol problem pri TCP paketoch na normalnej 1000Mbit sieti cez tunel bolo problem pretlacit 500-700kbit/s pri UDP paketoch to islo krasne na 2M ako je zadany limit... Toto sa dialo na vsetkych 3.x verziach az v 3.17 to ide ok



spojenie bolo PC s winxpp cez strukturu na CAT. 7 Gigabit switch Cisco a RB 133

Pouzivate wireless-test, nebo wireless?

wireless

Dnes jsem tam taky dal 3.17 na 433-AH vse se zda byt OK ale v queue simple se mi nezobrazuji rychlosti, stahnuta data, vlastne vse je na 0, nevite co stím???

A nemas nahodou nastavene v SQ unlimited? Musis tam nastavit nejakou hodnotu...je to uz tusim od verze 3.13

DRAKK píše:A nemas nahodou nastavene v SQ unlimited? Musis tam nastavit nejakou hodnotu...je to uz tusim od verze 3.13

Taky mě to nezobrazuje žádný protečený data... mám sice v SQ unlimited, ale podle mě by to mělo stejně zobrazovat něco. Má se nastavit ten max limit na záložce General, nebo na záložce Advanced Limit at???

Drakk ma pravdu. V zalozce General nesmi byt u policka "Max limit:" unlimited, stejne tak v zalozce Total a v policku "Total Max limit. Kdyz tam budou hodnoty bude to ukazovat data.....