6.42.4
Napsal: 19 Jun 2018 13:14
What's new in 6.42.4 (2018-Jun-15 14:14):
bridge - allow to make changes for bridge port when it is interface list;
bridge - fixed FastPath for bridge master interfaces (introduced in v6.42);
certificate - fixed "add-scep" template existence check when signing certificate;
chr - fixed adding MSTI entries;
chr - fixed boot on hosts older than Windows Server 2012 when running CHR on Hyper-V;
chr - fixed various network hang scenarios when running CHR on Hyper-V;
console - fixed script permissions if script is executed by other RouterOS service;
dhcpv4-server - fixed DHCP server that was stuck on invalid state;
health - changed "PSU-Voltage" to "PSU-State" for CRS328-4C-20S-4S+;
health - fixed incorrect PSU index for CRS328-4C-20S-4S+;
ipsec - improved reliability on IPsec hardware encryption for RB1100Dx4;
kidcontrol - fixed dynamically created firewall rules order;
led - added "dark-mode" functionality for hEX S and SXTsq 5 ac devices;
led - fixed CCR1016-12S-1S+ LED behaviour after Netinstall (introduced in v6.41rc58);
led - use routers uptime as a starting point when turning off LEDs if option was not enabled on boot;
ppp - fixed "hunged up" grammar to "hung up" within PPP log messages;
quickset - added missing wireless "channel-width" settings;
quickset - added support for "5ghz-a/n" band when CPE mode is used;
snmp - added remote CAP count OID for CAPsMAN;
snmp - fixed readings for CAPsMAN slave interfaces;
supout - added "partitions" section to supout file;
usb - properly detect USB 3.0 flash on RBM33G when jumper is removed;
userman - improved unique username generation process when adding batch of users;
w60g - improved RAM memoy allocation processes;
winbox - added missing "dscp" and "clamp-tcp-mss" settings to IPv6 tunnels;
winbox - allow to specify full URL in SCEP certificate signing process;
winbox - by default specify keepalive timeout value for tunnel type interfaces;
winbox - show "scep-url" for certificates;
winbox - show "System/Health" only on boards that have health monitoring;
winbox - show firmware upgrade message at the bottom of "System/RouterBOARD" menu;
wireless - enable all chains by default on devices without external antennas after configuration reset;
wireless - improved Nv2 reliability on ARM devices;
Podle mého spíše "údržbové" vydání.
bridge - allow to make changes for bridge port when it is interface list;
bridge - fixed FastPath for bridge master interfaces (introduced in v6.42);
certificate - fixed "add-scep" template existence check when signing certificate;
chr - fixed adding MSTI entries;
chr - fixed boot on hosts older than Windows Server 2012 when running CHR on Hyper-V;
chr - fixed various network hang scenarios when running CHR on Hyper-V;
console - fixed script permissions if script is executed by other RouterOS service;
dhcpv4-server - fixed DHCP server that was stuck on invalid state;
health - changed "PSU-Voltage" to "PSU-State" for CRS328-4C-20S-4S+;
health - fixed incorrect PSU index for CRS328-4C-20S-4S+;
ipsec - improved reliability on IPsec hardware encryption for RB1100Dx4;
kidcontrol - fixed dynamically created firewall rules order;
led - added "dark-mode" functionality for hEX S and SXTsq 5 ac devices;
led - fixed CCR1016-12S-1S+ LED behaviour after Netinstall (introduced in v6.41rc58);
led - use routers uptime as a starting point when turning off LEDs if option was not enabled on boot;
ppp - fixed "hunged up" grammar to "hung up" within PPP log messages;
quickset - added missing wireless "channel-width" settings;
quickset - added support for "5ghz-a/n" band when CPE mode is used;
snmp - added remote CAP count OID for CAPsMAN;
snmp - fixed readings for CAPsMAN slave interfaces;
supout - added "partitions" section to supout file;
usb - properly detect USB 3.0 flash on RBM33G when jumper is removed;
userman - improved unique username generation process when adding batch of users;
w60g - improved RAM memoy allocation processes;
winbox - added missing "dscp" and "clamp-tcp-mss" settings to IPv6 tunnels;
winbox - allow to specify full URL in SCEP certificate signing process;
winbox - by default specify keepalive timeout value for tunnel type interfaces;
winbox - show "scep-url" for certificates;
winbox - show "System/Health" only on boards that have health monitoring;
winbox - show firmware upgrade message at the bottom of "System/RouterBOARD" menu;
wireless - enable all chains by default on devices without external antennas after configuration reset;
wireless - improved Nv2 reliability on ARM devices;
Podle mého spíše "údržbové" vydání.