Verze 6.42.11

[goblajz]

What's new in 6.42.11 (2018-Dec-21 09:17):

MAJOR CHANGES IN v6.42.11:
----------------------
!) telnet - do not allow to set "tracefile" parameter;
----------------------

*) capsman - fixed "group-key-update" parameter not using correct units;
*) certificate - properly flush old CRLs when changing store location;
*) console - properly remove system note after configuration reset;
*) dhcpv6-server - properly handle DHCP requests that include prefix hint;
*) discovery - fixed malformed neighbor information for routers that has incomplete IPv6 configuration;
*) discovery - fixed neighbor discovery for PPP interfaces;
*) export - fixed "silent-boot" compact export;
*) gps - added "coordinate-format" parameter;
*) interface - improved system stability when including/excluding a list to itself;
*) kidcontrol - do not allow users with "read" policy to pause and resume kids;
*) led - fixed default LED configuration for RBMetalG-52SHPacn;
*) log - properly handle long echo messages;
*) lte - added support for more ZTE MF90 modems;
*) lte - disallow setting LTE interface as passthrough target;
*) package - use bundled package by default if standalone packages are installed as well;
*) resource - fixed "total-memory" reporting on ARM devices;
*) snmp - added "tx-ccq" ("mtxrWlStatTxCCQ") and "rx-ccq" ("mtxrWlStatRxCCQ") values;
*) snmp - do not initialise interface traps on bootup if they are not enabled;
*) switch - fixed MAC learning when disabling interfaces on devices with Atheros8327 and QCA8337 switch chips;
*) system - fixed situation when all configuration was not properly loaded on bootup;
*) timezone - fixed "Europe/Dublin" time zone;
*) upgrade - automatically uninstall standalone package if already installed in bundle;
*) webfig - do not show bogus VHT field in wireless interface advanced mode;
*) winbox - allow to change VHT rates when 5ghz-n/ac band is used;
*) winbox - renamed "Radius" to "RADIUS";
*) winbox - show "Switch" menu on RB4011iGS+5HacQ2HnD and RB4011iGS+;
*) wireless - added new "installation" parameter to specify router's location;
*) wireless - improved stability for 802.11ac;
*) wireless - improvements in wireless frequency selection;

[ludvik]

Nemyslel jsi 6.43.11?

[hapi]

ne, tohle všechno už měla 6.43.8.

6.43.11 nemá tolik věcí, prakticky pro nás nemá nic.

[Noxus28]

asi takto
What's new in 6.43.11 (2019-Feb-04 12:24):

ipsec - accept only valid path for "export-pub-key" parameter in "key" menu;
quickset - fixed "country" parameter not properly setting regulatory domain configuration;
smb - fixed possible buffer overflow;
w60g - fixed disconnection issues in PtMP setups;
wireless - improved antenna gain setting for devices with built in antennas;
wireless - show indoor/outdoor frequency limitations under "/interface wireless info country-info" command;

[emel]

na LHGG60G neodporucam davat 6.43.11 [stable] - pred upgradom RSSI na oboch stranach -49, po upgrade na jednej -56 a druhej -59

EDIT: po reboote sa jedna strana chytila pekne na -51 s MCS 8, ale druha mala signal 20 a MCS 1!
EDIT2: po 3. reboote je na oboch stranach naspat RSSI -49 a MCS 8

EDIT3: ono toto vlakno asi bolo myslene na 6.42.11 LONG-TERM nie STABLE...

[basty]

Mne to dělá taky. Každý reboot jiné čísla. To není vyloženě verzi.

[honzam]

Chtělo by to aby goblajz přejmenoval Topic a změnil changelog na 6.43.11

[basty]

Ale ten change log i datum sedí... Takže je to správné jen to není aktuální vůbec.

[honzam]

Ale ten change log i datum sedí... Takže je to správné jen to není aktuální vůbec.

To ano ale 6.42.11 vyšla někdy loni v prosinci. Kdežto topic zakládal dnes tak předpokládám že se to má týkat verze 6.43.11 která vyšla dnes
dedukce

[basty]

ano, je to popletal