WRT-311 změna MAC - rozchození konzole
Napsal: 10 May 2007 00:40
Zdravím,
Laboruji tady zrovna s WRT-311, pokud by se někomu hodila konzole pro zotavení tak tady je návod:
Připojení:
sys konektor s označením J4
Při pohledu od portu:
1 - VCC (3,2V)
2 - TX
3 - RX
4 - GND
nastavení terminálu:
Rychlost 38400
8 bit
žádná parita
1 stop bit
Xon/Soft
A hurá na to!
Po připojení vypíše asi něco takového:
UART1 output test ok
Uart init
mfid=000000c2 devid=00002249
Found 1 x 2M flash memory
---RealTek(RTL8186)at 2005.09.14-18:49+0800 version 1.3b [32bit](180MHz)
no sys signature at 00010000!
Jump to image start=0x80300000...
decompressing kernel:
Uncompressing Linux... done, booting the kernel.
done decompressing kernel.
early printk enabled
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock1 console=0 single
Calibrating delay loop... 178.99 BogoMIPS
Memory: 14252k/16384k available (1604k kernel code, 2132k reserved, 128k data, 4
8k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
check_wait... unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Serial driver version 6.02 (2003-03-12) with no serial options enabled
ttyS00 at 0x00c3 (irq = 3) is a rtl_uart1
state->flags=00000000
Realtek GPIO Driver for Flash Reload Default
block: 64 slots per queue, batch=16
PPP generic driver version 2.4.1
PPP MPPE Compression module registered
RealTek E-Flash System Driver. (C) 2002 RealTek Corp.
Found 1 x 2M Byte MXIC MX29LV160AB at 0xbe000000
Creating 2 MTD partitions on "DiskOnChip Millennium":
0x00000000-0x00100000 : "boot+cfg+linux"
0x00100000-0x00200000 : "root fs"
RTL8185 driver version 1.9 (2006-03-16)
8186NIC Ethernet driver v0.0.5 (Mar 3, 2006)
eth0: RTL8186-NIC at 0xbd200000, 00:01:02:03:04:05, IRQ 4
eth1: RTL8186-NIC at 0xbd300000, 04:05:06:07:08:09, IRQ 5
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 2048)
ip_conntrack version 2.1 (128 buckets, 1024 max) - 312 bytes per conntrack
PPTP netfilter connection tracking: registered
PPTP netfilter NAT helper: registered
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 48k freed
mount /proc file system ok!
mount /var file system ok!
init started: BusyBox v1.1.0-pre1 (2006.05.29-20:45+0000) multi-call binary
BusyBox v1.1.0-pre1 (2006.05.29-20:45+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Setting opmode
Killing tasks then interfaces
Setting MACs
Setup bridge(s)
device eth0 entered promiscuous mode
eth0:phy is 8305
device wlan0 entered promiscuous mode
device eth1 entered promiscuous mode
eth1:phy is 8305
br0: port 2(wlan0) entering disabled state
device wlan0 left promiscuous mode
br0: port 3(eth1) entering listening state
br0: port 1(eth0) entering listening state
br0: port 3(eth1) entering learning state
br0: port 3(eth1) entering forwarding state
br0: topology change detected, propagating
br0: port 1(eth0) entering learning state
br0: port 1(eth0) entering forwarding state
br0: topology change detected, propagating
Setting up IP
Starting services
Setting Routes
Setting up Firewall
#
Jinak pokud by mi někdo poradil jak uložit změnu MAC adresy po rebootu byl bych vděčny!
Hodně zdaru!
Laboruji tady zrovna s WRT-311, pokud by se někomu hodila konzole pro zotavení tak tady je návod:
Připojení:
sys konektor s označením J4
Při pohledu od portu:
1 - VCC (3,2V)
2 - TX
3 - RX
4 - GND
nastavení terminálu:
Rychlost 38400
8 bit
žádná parita
1 stop bit
Xon/Soft
A hurá na to!
Po připojení vypíše asi něco takového:
UART1 output test ok
Uart init
mfid=000000c2 devid=00002249
Found 1 x 2M flash memory
---RealTek(RTL8186)at 2005.09.14-18:49+0800 version 1.3b [32bit](180MHz)
no sys signature at 00010000!
Jump to image start=0x80300000...
decompressing kernel:
Uncompressing Linux... done, booting the kernel.
done decompressing kernel.
early printk enabled
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock1 console=0 single
Calibrating delay loop... 178.99 BogoMIPS
Memory: 14252k/16384k available (1604k kernel code, 2132k reserved, 128k data, 4
8k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
check_wait... unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Serial driver version 6.02 (2003-03-12) with no serial options enabled
ttyS00 at 0x00c3 (irq = 3) is a rtl_uart1
state->flags=00000000
Realtek GPIO Driver for Flash Reload Default
block: 64 slots per queue, batch=16
PPP generic driver version 2.4.1
PPP MPPE Compression module registered
RealTek E-Flash System Driver. (C) 2002 RealTek Corp.
Found 1 x 2M Byte MXIC MX29LV160AB at 0xbe000000
Creating 2 MTD partitions on "DiskOnChip Millennium":
0x00000000-0x00100000 : "boot+cfg+linux"
0x00100000-0x00200000 : "root fs"
RTL8185 driver version 1.9 (2006-03-16)
8186NIC Ethernet driver v0.0.5 (Mar 3, 2006)
eth0: RTL8186-NIC at 0xbd200000, 00:01:02:03:04:05, IRQ 4
eth1: RTL8186-NIC at 0xbd300000, 04:05:06:07:08:09, IRQ 5
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 2048)
ip_conntrack version 2.1 (128 buckets, 1024 max) - 312 bytes per conntrack
PPTP netfilter connection tracking: registered
PPTP netfilter NAT helper: registered
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 48k freed
mount /proc file system ok!
mount /var file system ok!
init started: BusyBox v1.1.0-pre1 (2006.05.29-20:45+0000) multi-call binary
BusyBox v1.1.0-pre1 (2006.05.29-20:45+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Setting opmode
Killing tasks then interfaces
Setting MACs
Setup bridge(s)
device eth0 entered promiscuous mode
eth0:phy is 8305
device wlan0 entered promiscuous mode
device eth1 entered promiscuous mode
eth1:phy is 8305
br0: port 2(wlan0) entering disabled state
device wlan0 left promiscuous mode
br0: port 3(eth1) entering listening state
br0: port 1(eth0) entering listening state
br0: port 3(eth1) entering learning state
br0: port 3(eth1) entering forwarding state
br0: topology change detected, propagating
br0: port 1(eth0) entering learning state
br0: port 1(eth0) entering forwarding state
br0: topology change detected, propagating
Setting up IP
Starting services
Setting Routes
Setting up Firewall
#
Jinak pokud by mi někdo poradil jak uložit změnu MAC adresy po rebootu byl bych vděčny!
Hodně zdaru!